 |
 |
 |
|
 
INCRA 32" x 21" Table Saw Router Table Top - Left Side of Blade for 30" - 31" Table Saws (W/TSRTHW)
Take advantage of your INCRA TS Fence System's positioning accuracy and repeatability and put the space next to your saw to work! INCRA's TS Router Tables are an easy way to add a second router table to your shop or simply make better use of space in a small shop. Installing a router table on the left side of the saw allows excellent access around the router bit and takes advantage of the LS positioner's full capacity, plus it's twice as wide as the saw's original cast iron extension. The fence system's base assembly is slid down the rails to the left for routing operations, and the INCRA System's Rail Stops can provide perfect repeatability between routing and sawing operations.
This new router table is specifically sized to complement newer-model cabinet saws with oversize cast iron tops that measure between 30" and 31" deep along the miter slot. The table attaches to the rails of INCRA TS-LS or TS-III fence systems, and since it replaces the left-side cast iron extension wing, it's not compatible with saws that have a motor housing protruding from the left side of the cabinet.
Horizontal-grade high pressure laminate is applied to the top and bottom of the MDF core using heat and 100,000 pounds of pressure for a balanced, stable construction. Each computer-machined plate opening also has ten flat head leveling screws that form a solid steel base to support the plate, and the plates are conveniently leveled from above the table through access holes in the router plates.
|
TS-RT Support Kit
The router tables include heavy steel hardware to attach them to the rails of the TS-LS and TS-III rip fence systems, so no attachment to the table saw is necessary. The hardware is slotted to allow fine-tuning the height of the tables, and the hardware is also available separately for mounting user-made router tables and filler boards to the
INCRA TS Rails
.
|
|
Solid Aluminum MagnaLOCK Plate & 3 Rings
All INCRA Router Tables come standard with a 3/8" solid aluminum Magna-Lock router mounting plates that are pre-drilled for the most popular routers. The high energy, rare-earth magnets of the Magna-Lock system allows you to instantly remove or install the included steel reducing rings, and the magnets hold the ring secure and perfectly flush with the plate every time. It's simply the most convenient and best-performing ring system available.
All of our mounting plates include three laser-cut steel rings with 1", 2-1/8" and 3-5/8" openings. A simple quarter turn of the corner mounted Cam-Lock securely holds the plate snugly in the router table's recess.
|
Note - This table is not compatible with the unique Mast-R-Lift-II-R sold by Rockler, which uses a narrower 8-1/4"-wide top plate.
Router plate size: 9-1/4" x 11-3/4" x 3/8"
Actual table size:
31.580" x 21.080" +/-0.020"
Table thickness:
1.100" +/-0.030"
All INCRA Router Tables and Combos include the outstanding MagnaLOCK Aluminum Router Mounting Plate, but you can also upgrade to an INCRA Router Lift for the ultimate in convenience and accuracy.
Note: Router plates are pre-drilled to accept a variety of popular routers. Specify your router preference when placing an order. (See Compatibility Chart)
Popular Accessories & Upgrades:
|
|
Improved dust collection for all of your router table work! Use the power of your shop's dust collection system to grab sawdust where it's produced on your router table! The CleanSweep cabinet attaches to the underside of laminated MDF or phenolic router tables from INCRA, Woodpeckers, JessEm, and many others. This must-have accessory is one of the easiest ways to improve the quality of your router table time!
|
|
Upgrade your combo to the ultimate in convenience with an INCRA Router Lift!If you're ordering a router lift, you can use the drop-down selector at the top of this page to remove the gold aluminum router plate from the combo for a $45 credit.
|
|
A greater variety of ring sizes gives you more support for small parts or when using different diameter.Available as a set or individually with a dozen to choose from, including a ring to accept guide bushings.
|
|
A new router table setup deserves a fresh router.Check out our full selection!
|
|
28" x 21" TS Router Table (standard saws)
32" x 21" Left-side TS Router Table (oversize saws) |
|
The Left-side router tables permit maximum fence system range and offers open access from the end of the table saw by sliding the LS positioner assembly down the rails. At 21" wide, they double the surface area of the saw's original extension wing and don't require the addition of support legs.
The 28" x 21" table is for use with TS-LS or TS-III systems mounted to standard-size saws that measure between 27" and 28" deep along the miter slot.
The 32" x 21" table is for use with TS-LS or TS-III systems mounted to oversize saws that measure between 30" and 31" deep along the miter slot.
Left-side TS Router Table Tops include:
 Solid Aluminum MagnaLOCK Plate & 3 Rings (1", 2-1/8" & 3-5/8")TS Router Table Support Hardware (TSRTHW)
Note: This router table replaces the saw's left-side extension wing, and therefore is not compatible with saws that have a motor housing protruding from the left side of the saw's cabinet. |
|
|
28" x 32" Right-side TS Router Table (standard saws) 32" x 32" Right-side TS Router Table (oversize saws) |
|
The Right-side router tables serve double duty as a work surface extension and include full size 3/8" x 3/4" T-Slot miter channels. The positioner's base assembly typically does not need to be moved on the rails for router work, but the base assembly can be reversed on the rails for the best capacity and router access.
The 28" x 32" table is for use with TS-LS or TS-III systems mounted to standard-size saws that measure between 27" and 28" deep along the miter slot.
The 32" x 32" table is for use with TS-LS or TS-III systems mounted to oversize saws that measure between 30" and 31" deep along the miter slot.
For INCRA TS fence systems with the standard 72" rails / 32" rip capacity, the router table mounts in place of the saw's original right-side extension wing. Owners of TS fence systems with 92" rails / 52" rip capacity will have the option of mounting the router table outboard of the saw's right-side extension wing.
Right-side TS Router Table Tops include:
Solid Aluminum MagnaLOCK Plate & 3 Rings (1", 2-1/8" & 3-5/8")
TS Router Table Support Hardware (TSRTHW)
Note: TS Rail Support Legs are highly recommended.
Note: This router table is not a good choice if your saw has a motor housing protruding from the right side of the cabinet AND your TS fence system has the standard 72" rails / 32" rip capacity. |
|
|
|
 |
|
 |
|